Next Page Previous Page Home Tools & Aids Search Handbook
5. Process Improvement
5.5. Advanced topics
5.5.4. What is a mixture design?

5.5.4.4.

Constrained mixture designs
Upper and/or lower bound constraints may be present In mixture designs when there are constraints on the component proportions, these are often upper and/or lower bound constraints of the form Li <= xi <= Ui, i = 1, 2,..., q, where Li is the lower bound for the i-th component and Ui the upper bound for the i-th component. The general form of the constrained mixture problem is
Typical additional constraints
    x1 + x2 + ... + xq = 1

    Li <= xi <= Ui,   for i = 1, 2,..., q

with Li >= 0 and Ui >= 1.
Example using only lower bounds Consider the following case in which only the lower bounds in the above equation are imposed, so that the constrained mixture problem becomes
    x1 + x2 + ... + xq = 1

    Li <= xi <= 1,   for i = 1, 2,..., q

Assume we have a three-component mixture problem with constraints
    0.3 <= x1     0.4 <= x2     0.1 <= x3
Feasible mixture region The feasible mixture space is shown in the figure below. Note that the existence of lower bounds does not affect the shape of the mixture region, it is still a simplex region. In general, this will always be the case if only lower bounds are imposed on any of the component proportions.
Diagram showing the feasible mixture space
Diagram showing the feasible mixture space
FIGURE 5.12  The Feasible Mixture Space (Shaded Region) for Three Components with Lower Bounds
A simple transformation helps in design construction and analysis Since the new region of the experiment is still a simplex, it is possible to define a new set of components that take on the values from 0 to 1 over the feasible region. This will make the design construction and the model fitting easier over the constrained region of interest. These new components (x(i)^(*)) are called pseudo components and are defined using the following formula
Formula for pseudo components
    x(i)* = (x(i) - L)/(1 - L)
with
    L = SUM[i=1 to q][L(i)] < 1
denoting the sum of all the lower bounds.
Computation of the pseudo components for the example In the three component example above, the pseudo components are
x1* = (x1-0.3)/0.2; x2* = (x2 - 0.4)/0.2; x3* = (x3-0.1)/0.2
Constructing the design in the pseudo components Constructing a design in the pseudo components is accomplished by specifying the design points in terms of the x(i)^(*) and then converting them to the original component settings using
    xi = Li + (1 - L)x(i)^(*)
Select appropriate design In terms of the pseudo components, the experimenter has the choice of selecting a Simplex-Lattice or a Simplex-Centroid design, depending on the objectives of the experiment.
Simplex-centroid design example (after transformation) Suppose, we decided to use a Simplex-centroid design for the three-component experiment. The table below shows the design points in the pseudo components, along with the corresponding setting for the original components.
Table showing the design points in both the pseudo components and the original components
TABLE 5.5  Pseudo Component Settings and Original Component Settings, Three-Component Simplex-Centroid Design
Pseudo Components   Original Components
X1 X2 X3   x(1)* x(2)* x(3)*
1 0 0   0.5 0.4 0.1
0 1 0   0.3 0.6 0.1
0 0 1   0.3 0.4 0.3
0.5 0.5 0   0.4 0.5 0.1
0.5 0 0.5   0.4 0.4 0.2
0 0.5 0.5   0.3 0.5 0.2
0.3333 0.3333 0.3333   0.3667 0.4667 0.1666
Use of pseudo components (after transformation) is recommended It is recommended that the pseudo components be used to fit the mixture model. This is due to the fact that the constrained design space will usually have relatively high levels of multicollinearity among the predictors. Once the final predictive model for the pseudo components has been determined, the equation in terms of the original components can be determined by substituting the relationship between xi and x(i)*.
D-optimal designs can also be used Computer-aided designs (D-optimal, for example) can be used to select points for a mixture design in a constrained region. See Myers and Montgomery (1995) for more details on using D-optimal designs in mixture experiments.
Extreme vertice designs anre another option Note: There are other mixture designs that cover only a sub-portion or smaller space within the simplex. These types of mixture designs (not covered here) are referred to as extreme vertices designs. (See chapter 11 of Myers and Montgomery (1995) or Cornell (1990).
Home Tools & Aids Search Handbook Previous Page Next Page